? semiconductor components industries, llc, 2000 august, 2000 rev. 4 1 publication order number: mc14070b/d mc14070b, mc14077b cmos ssi quad exclusive aoro and anoro gates the mc14070b quad exclusive or gate and the mc14077b quad exclusive nor gate are constructed with mos pchannel and nchannel enhancement mode devices in a single monolithic structure. these complementary mos logic gates find primary use where low power dissipation and/or high noise immunity is desired. ? supply voltage range = 3.0 vdc to 18 vdc ? all outputs buffered ? capable of driving two lowpower ttl loads or one lowpower schottky ttl load over the rated temperature range ? double diode protection on all inputs ? mc14070b e replacement for cd4030b and cd4070b types ? mc14077b e replacement for cd4077b type maximum ratings (voltages referenced to v ss ) (note 2.) symbol parameter value unit v dd dc supply voltage range 0.5 to +18.0 v v in , v out input or output voltage range (dc or transient) 0.5 to v dd + 0.5 v i in , i out input or output current (dc or transient) per pin 10 ma p d power dissipation, per package (note 3.) 500 mw t a ambient temperature range 55 to +125 c t stg storage temperature range 65 to +150 c t l lead temperature (8second soldering) 260 c 2. maximum ratings are those values beyond which damage to the device may occur. 3. temperature derating: plastic ap and d/dwo packages: 7.0 mw/ c from 65 c to 125 c this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this highimpedance circuit. for proper operation, v in and v out should be constrained to the range v ss (v in or v out ) v dd . unused inputs must always be tied to an appropriate logic voltage level (e.g., either v ss or v dd ). unused outputs must be left open. http://onsemi.com xx = specific device code a = assembly location wl, l = wafer lot yy, y = year ww, w = work week device package shipping ordering information mc140xxbcp pdip14 2000/box mc140xxbd soic14 2750/box mc140xxbdr2 soic14 2500/tape & reel mc140xxbf soeiaj14 see note 1. marking diagrams 1 14 pdip14 p suffix case 646 mc140xxbcp awlyyww soic14 d suffix case 751a 1 14 140xxb awlyww soeiaj14 f suffix case 965 1 14 mc140xxb alyw mc140xxbfel soeiaj14 see note 1. 1. for ordering information on the eiaj version of the soic packages, please contact your local on semiconductor representative.
mc14070b, mc14077b http://onsemi.com 2 pin assignment 11 12 13 14 8 9 10 5 4 3 2 1 7 6 out c out d in 1 d in 2 d v dd in 1 c in 2 c out b out a in 2 a in 1 a v ss in 2 b in 1 b figure 1. power dissipation test circuit and waveform v dd v in c l * i dd 20 ns 20 ns v dd v ss 90% 50% 10% v in 1/f 50% duty cycle *inverted output on mc14077b only. figure 2. switching time test circuit and waveforms v dd c l 20 ns v ss v ss 90% output # * 20 ns v oh v ol v dd t thl t tlh 50% 10% 90% 50% 10% t plh t phl input *inverted output on mc14077b only. pulse generator #connect unused input to v dd for mc14070b, to v ss for mc14077b. mc14070b quad exclusive or gate mc14077b quad exclusive nor gate 13 11 12 9 8 6 5 2 1 10 4 3 13 12 9 8 6 5 2 1 11 10 4 3 v dd = pin 14 v ss = pin 7 (both devices)
mc14070b, mc14077b http://onsemi.com 3 ????????????????????????????????? ????????????????????????????????? electrical characteristics (voltages referenced to v ss ) ??????????? ??????????? ???? ???? ?? ?? v dd ?????? ?????? 55 c ???????? ???????? 25 c ????? ????? 125 c ??? ??? ??????????? ??????????? characteristic ???? ???? symbol ?? ?? v dd vdc ???? ???? min ??? ??? max ??? ??? min ???? ???? typ (4.) ??? ??? max ??? ??? min ??? ??? max ??? ??? unit ??????????? ? ????????? ? ??????????? output voltage a0o level v in = v dd or 0 ???? ? ?? ? ???? v ol ?? ?? ?? 5.0 10 15 ???? ? ?? ? ???? e e e ??? ? ? ? ??? 0.05 0.05 0.05 ??? ? ? ? ??? e e e ???? ? ?? ? ???? 0 0 0 ??? ? ? ? ??? 0.05 0.05 0.05 ??? ? ? ? ??? e e e ??? ? ? ? ??? 0.05 0.05 0.05 ??? ? ? ? ??? vdc ??????????? ? ????????? ? ??????????? a1o level v in = 0 or v dd ???? ? ?? ? ???? v oh ?? ?? ?? 5.0 10 15 ???? ? ?? ? ???? 4.95 9.95 14.95 ??? ? ? ? ??? e e e ??? ? ? ? ??? 4.95 9.95 14.95 ???? ? ?? ? ???? 5.0 10 15 ??? ? ? ? ??? e e e ??? ? ? ? ??? 4.95 9.95 14.95 ??? ? ? ? ??? e e e ??? ? ? ? ??? vdc ??????????? ? ????????? ? ? ????????? ? ??????????? input voltage a0o level (v o = 4.5 or 0.5 vdc) (v o = 9.0 or 1.0 vdc) (v o = 13.5 or 1.5 vdc) ???? ? ?? ? ? ?? ? ???? v il ?? ?? ?? ?? 5.0 10 15 ???? ? ?? ? ? ?? ? ???? e e e ??? ? ? ? ? ? ? ??? 1.5 3.0 4.0 ??? ? ? ? ? ? ? ??? e e e ???? ? ?? ? ? ?? ? ???? 2.25 4.50 6.75 ??? ? ? ? ? ? ? ??? 1.5 3.0 4.0 ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? 1.5 3.0 4.0 ??? ? ? ? ? ? ? ??? vdc ??????????? ? ????????? ? ? ????????? ? ??????????? a1o level (v o = 0.5 or 4.5 vdc) (v o = 1.0 or 9.0 vdc) (v o = 1.5 or 13.5 vdc) ???? ? ?? ? ? ?? ? ???? v ih ?? ?? ?? ?? 5.0 10 15 ???? ? ?? ? ? ?? ? ???? 3.5 7.0 11 ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? 3.5 7.0 11 ???? ? ?? ? ? ?? ? ???? 2.75 5.50 8.25 ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? 3.5 7.0 11 ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? vdc ??????????? ? ????????? ? ? ????????? ? ? ????????? ? ??????????? output drive current (v oh = 2.5 vdc) source (v oh = 4.6 vdc) (v oh = 9.5 vdc) (v oh = 13.5 vdc) ???? ? ?? ? ? ?? ? ? ?? ? ???? i oh ?? ?? ?? ?? ?? 5.0 5.0 10 15 ???? ? ?? ? ? ?? ? ? ?? ? ???? 3.0 0.64 1.6 4.2 ??? ? ? ? ? ? ? ? ? ? ??? e e e e ??? ? ? ? ? ? ? ? ? ? ??? 2.4 0.51 1.3 3.4 ???? ? ?? ? ? ?? ? ? ?? ? ???? 4.2 0.88 2.25 8.8 ??? ? ? ? ? ? ? ? ? ? ??? e e e e ??? ? ? ? ? ? ? ? ? ? ??? 1.7 0.36 0.9 2.4 ??? ? ? ? ? ? ? ? ? ? ??? e e e e ??? ? ? ? ? ? ? ? ? ? ??? madc ??????????? ? ????????? ? ??????????? (v ol = 0.4 vdc) sink (v ol = 0.5 vdc) (v ol = 1.5 vdc) ???? ? ?? ? ???? i ol ?? ?? ?? 5.0 10 15 ???? ? ?? ? ???? 0.64 1.6 4.2 ??? ? ? ? ??? e e e ??? ? ? ? ??? 0.51 1.3 3.4 ???? ? ?? ? ???? 0.88 2.25 8.8 ??? ? ? ? ??? e e e ??? ? ? ? ??? 0.36 0.9 2.4 ??? ? ? ? ??? e e e ??? ? ? ? ??? madc ??????????? ??????????? input current ???? ???? i in ?? ?? 15 ???? ???? e ??? ??? 0.1 ??? ??? e ???? ???? 0.00001 ??? ??? 0.1 ??? ??? e ??? ??? 1.0 ??? ??? m adc ??????????? ? ????????? ? ??????????? input capacitance (v in = 0) ???? ? ?? ? ???? c in ?? ?? ?? e ???? ? ?? ? ???? e ??? ? ? ? ??? e ??? ? ? ? ??? e ???? ? ?? ? ???? 5.0 ??? ? ? ? ??? 7.5 ??? ? ? ? ??? e ??? ? ? ? ??? e ??? ? ? ? ??? pf ??????????? ? ????????? ? ??????????? quiescent current (per package) ???? ? ?? ? ???? i dd ?? ?? ?? 5.0 10 15 ???? ? ?? ? ???? e e e ??? ? ? ? ??? 0.25 0.5 1.0 ??? ? ? ? ??? e e e ???? ? ?? ? ???? 0.0005 0.0010 0.0015 ??? ? ? ? ??? 0.25 0.5 1.0 ??? ? ? ? ??? e e e ??? ? ? ? ??? 7.5 15 30 ??? ? ? ? ??? m adc ??????????? ? ????????? ? ? ????????? ? ? ????????? ? ??????????? total supply current (5.) (6.) (dynamic plus quiescent, per package) (c l = 50 pf on all outputs, all buffers switching) ???? ? ?? ? ? ?? ? ? ?? ? ???? i t ?? ?? ?? ?? ?? 5.0 10 15 ????????????????? ? ??????????????? ? ? ??????????????? ? ? ??????????????? ? ????????????????? i t = (0.3 m a/khz) f + i dd i t = (0.6 m a/khz) f + i dd i t = (0.9 m a/khz) f + i dd ??? ? ? ? ? ? ? ? ? ? ??? m adc ??????????? ? ????????? ? ? ????????? ? ? ????????? ? ??????????? output rise and fall times (5.) (c l = 50 pf) t tlh , t thl = (1.35 ns/pf) c l + 33 ns t tlh , t thl = (0.60 ns/pf) c l + 20 ns t tlh , t thl = (0.40 ns/pf) c l + 20 ns ???? ? ?? ? ? ?? ? ? ?? ? ???? t tlh , t thl ?? ?? ?? ?? ?? 5.0 10 15 ???? ? ?? ? ? ?? ? ? ?? ? ???? e e e ??? ? ? ? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ? ? ? ??? e e e ???? ? ?? ? ? ?? ? ? ?? ? ???? 100 50 40 ??? ? ? ? ? ? ? ? ? ? ??? 200 100 80 ??? ? ? ? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ? ? ? ??? ns ??????????? ? ????????? ? ? ????????? ? ??????????? propagation delay times (5.) (c l = 50 pf) t plh , t phl = (0.90 ns/pf) c l + 130ns t plh , t phl = (0.36 ns/pf) c l + 57 ns t plh , t phl = (0.26 ns/pf) c l + 37 ns ???? ? ?? ? ? ?? ? ???? t plh , t phl ?? ?? ?? ?? 5.0 10 15 ???? ? ?? ? ? ?? ? ???? e e e ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? e e e ???? ? ?? ? ? ?? ? ???? 175 75 55 ??? ? ? ? ? ? ? ??? 350 150 110 ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? e e e ??? ? ? ? ? ? ? ??? ns 4. data labelled atypo is not to be used for design purposes but is intended as an indication of the ic's potential performance. 5. the formulas given are for the typical characteristics only at 25 c. 6. to calculate total supply current at loads other than 50 pf: i t (c l ) = i t (50 pf) + (c l 50) vfk where: i t is in m h (per package), c l in pf, v = (v dd v ss ) in volts, f in khz is input frequency, and k = 0.002.
mc14070b, mc14077b http://onsemi.com 4 package dimensions p suffix plastic dip package case 64606 issue m 17 14 8 b a dim min max min max millimeters inches a 0.715 0.770 18.16 18.80 b 0.240 0.260 6.10 6.60 c 0.145 0.185 3.69 4.69 d 0.015 0.021 0.38 0.53 f 0.040 0.070 1.02 1.78 g 0.100 bsc 2.54 bsc h 0.052 0.095 1.32 2.41 j 0.008 0.015 0.20 0.38 k 0.115 0.135 2.92 3.43 l m --- 10 --- 10 n 0.015 0.039 0.38 1.01 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of leads when formed parallel. 4. dimension b does not include mold flash. 5. rounded corners optional. f hg d k c seating plane n t 14 pl m 0.13 (0.005) l m j 0.290 0.310 7.37 7.87
mc14070b, mc14077b http://onsemi.com 5 package dimensions d suffix plastic soic package case 751a03 issue f notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. a b g p 7 pl 14 8 7 1 m 0.25 (0.010) b m s b m 0.25 (0.010) a s t t f r x 45 seating plane d 14 pl k c j m dim min max min max inches millimeters a 8.55 8.75 0.337 0.344 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.228 0.244 r 0.25 0.50 0.010 0.019
mc14070b, mc14077b http://onsemi.com 6 package dimensions f suffix plastic eiaj soic package case 96501 issue o h e a 1 dim min max min max inches --- 2.05 --- 0.081 millimeters 0.05 0.20 0.002 0.008 0.35 0.50 0.014 0.020 0.18 0.27 0.007 0.011 9.90 10.50 0.390 0.413 5.10 5.45 0.201 0.215 1.27 bsc 0.050 bsc 7.40 8.20 0.291 0.323 0.50 0.85 0.020 0.033 1.10 1.50 0.043 0.059 0 0.70 0.90 0.028 0.035 --- 1.42 --- 0.056 a 1 h e q 1 l e 10 0 10 l e q 1 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions d and e do not include mold flash or protrusions and are measured at the parting line. mold flash or protrusions shall not exceed 0.15 (0.006) per side. 4. terminal numbers are shown for reference only. 5. the lead width dimension (b) does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the lead width dimension at maximum material condition. dambar cannot be located on the lower radius or the foot. minimum space between protrusions and adjacent lead to be 0.46 ( 0.018). 0.13 (0.005) m 0.10 (0.004) d z e 1 14 8 7 e a b view p c l detail p m a b c d e e 0.50 m z
mc14070b, mc14077b http://onsemi.com 7 notes
mc14070b, mc14077b http://onsemi.com 8 on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information central/south america: spanish phone : 3033087143 (monfri 8:00am to 5:00pm mst) email : onlitspanish@hibbertco.com asia/pacific : ldc for on semiconductor asia support phone : 3036752121 (tuefri 9:00am to 1:00pm, hong kong time) toll free from hong kong & singapore: 00180044223781 email : onlitasia@hibbertco.com japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402745 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. mc14070b/d north america literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com fax response line: 3036752167 or 8003443810 toll free usa/canada n. american technical support : 8002829855 toll free usa/canada europe: ldc for on semiconductor european support german phone : (+1) 3033087140 (monfri 2:30pm to 7:00pm cet) email : onlitgerman@hibbertco.com french phone : (+1) 3033087141 (monfri 2:00pm to 7:00pm cet) email : onlitfrench@hibbertco.com english phone : (+1) 3033087142 (monfri 12:00pm to 5:00pm gmt) email : onlit@hibbertco.com european tollfree access*: 0080044223781 *available from germany, france, italy, uk
|
